Coventry’s homes tell the story of the city. There are Victorian and Edwardian terraces in Earlsdon, Chapelfields and Stoke, interwar semis built as the motor and engineering industries grew, large post-war estates from the years of rebuilding after the Second World War, and plenty of new homes and student housing today. We’re RCR Connections Ltd, and we plaster and render homes all over Coventry, including Earlsdon, Chapelfields, Spon End, Coundon, Radford, Holbrooks, Foleshill, Stoke, Wyken, Walsgrave, Binley, Willenhall, Cheylesmore, Styvechale, Finham, Canley, Tile Hill, Eastern Green and Allesley.

For the outside of the house, see our page on rendering in Coventry, which covers K-Rend monocouche and silicone render, re-renders and render repairs.

Plastering and rendering is the only thing we do. The team has 62 years of combined experience. That means you get straight advice about your walls, ceilings and render, from people who see the same problems week in, week out.

Below you’ll find each of our services explained with Coventry homes in mind, a tour of the city’s housing and the problems each type throws up, three planning checks to make before any rendering, and practical notes on drying, choosing a plasterer and getting a quote.

Plastering and rendering in Coventry: our services

Plastering

Plastering takes a surface from bare masonry or new plasterboard to a smooth, solid finish ready for decoration. On brick and block, we apply a backing coat to level the wall, then a finish coat. On plasterboard, joints are taped and a finish coat goes over the top.

A lot of the full plastering we do in Coventry is on renovation projects: terraced houses stripped back to the brick, back rooms knocked into kitchens, extensions, and student houses being reconfigured. We choose the backing to suit each wall, because old soft brick, newer block and repaired areas all behave differently.

Skimming

Skimming means applying a thin coat of finishing plaster over a sound wall or ceiling. It’s the go-to job for walls that are tired, cracked, patched or marked after wallpaper removal, and it gives a smooth surface that takes paint well.

Before skimming we always check the wall. Tapping tells us where plaster has come away from the brick, and we look for damp, salts and cracks. If we find hollow areas, they’re cut out and patched first. Skimming over blown plaster just means you’ll be redoing the job sooner than you should.

Re-plastering and patch repairs

Some walls are past saving with a skim. When the plaster crumbles under your thumb, sounds drummy across a large area, or is stained white with salts after a damp problem, the honest answer is to strip it off back to the brick and start again. We prepare the bare wall, apply a backing coat suited to the masonry and finish it smooth. In Coventry this comes up most on the ground floors of older terraces after a new damp-proof course, on chimney breasts, and in houses where generations of owners have patched with whatever was in the shed.

Patch repairs are the smaller jobs that come up all the time: making good after rewires and new alarm systems, filling holes where pipes and radiators have moved, repairing walls after bathroom and kitchen refits, and fixing corners that have taken a knock. We build patches up in layers and finish them flush, so they disappear once painted. Landlords of shared houses often have several of these to deal with at the end of each academic year, and we can work to tight turnaround dates.

Artex and textured ceiling skimming

Textured ceilings are common in Coventry homes decorated in the 1960s, 70s and 80s, from stipples in Tile Hill and Canley to swirls in Wyken and Walsgrave. Most owners want them gone and a plain, flat ceiling in their place.

The two usual routes are a sealing coat followed by skimming in several passes, or screwing new plasterboard across the joists and skimming the new boards. If the pattern is heavy, or the ceiling has cracks or a slight dip, boarding is normally the better bet. Either way the old texture stays where it is, locked behind the new surface.

That’s deliberate. Artex-type coatings put up before 2000 might contain asbestos, and covering them is far safer than disturbing them. Anyone who wants the texture physically removed should arrange a test first. We explain this more in our guide to skimming over Artex.

Dry lining and plasterboard

Dry lining is plasterboard fixed to walls and ceilings, using adhesive dabs, battens or a timber or metal stud frame, then finished with a skim or with tape and joint.

We board loft conversions, extensions, garage conversions and new stud walls, and replace ceilings that have been damaged by leaks. In shared houses, new partitions to create extra rooms or en-suites are often part of the job. On older solid walls we check for damp before boarding, because moisture trapped behind boards can lead to mould.

Monocouche render, including K-Rend monocouche

Think of K-Rend monocouche as render with the paint already built in. It’s a monocouche, or through-coloured, product: the pigment is part of the mix, so when the surface is scraped back after application, what you see is the finished colour. There’s nothing to repaint every few years, and small scuffs don’t reveal a different colour underneath.

Around Coventry we use it to give interwar and post-war houses a fresh face where brick has weathered unevenly or pebbledash has had its day, and to finish block-built extensions so they look smart from day one. The K-Rend monocouche page on our site walks through the process step by step.

Silicone render

Silicone render goes on as the last layer of a system: a base coat with glass-fibre mesh bedded into it, a primer, then the textured silicone top coat. Silicone resins make the finish shed water, so rain beads up and rolls away, taking dirt with it. It’s also slightly flexible, which helps it cope with the small seasonal movement every building has.

That makes it a good fit for gable ends that take the brunt of the weather, homes backing onto trees or parks, and elevations that stay in shade most of the day. It’s the normal finish on insulated render too. If you’re torn between finishes, our comparison of K-Rend monocouche, silicone and sand and cement render lays out the pros and cons.

Sand and cement render

Plenty of Coventry houses already wear painted sand and cement render, and for those it’s often the natural choice for repairs and re-coats. It’s mixed on site, applied by hand in a scratch coat and a top coat, left to cure, then decorated with masonry paint. It’s strong, simple to patch and well suited to garden walls, plinths and outbuildings.

The catch is that it’s a hard, fairly impermeable material. On Victorian solid brick it can hold moisture in the wall rather than letting it escape, which leads to damp inside and render cracking off outside. For those houses, we’d usually steer you towards a breathable alternative.

Insulated render

With insulated render, rigid insulation boards are fixed to the outside face of the walls, then sealed in with a mesh-reinforced base coat and a finishing render. The house effectively gets a warm overcoat, which is why the system is aimed at solid walls that lose heat easily.

Parts of Coventry’s post-war housing have solid walls or were built using non-traditional systems, and for some of those homes insulated render is worth looking at. It’s a serious undertaking, though. Sills often need extending, downpipes and cables moving, the roofline adjusting, and there’s paperwork: building regulations always, and planning permission in some cases. We’ll go through all of that with you so there are no surprises later.

Render repairs

Most failing render we see around the city started with something small. A hairline crack lets rain in, the water freezes, and the render slowly loses its grip until a section bulges or drops. Overflowing gutters, render that was carried down below the damp-proof course, and corner beads that have rusted through all speed the process up.

A repair might mean raking out and filling cracks, cutting back hollow patches to sound edges and re-rendering them, rebuilding broken corners, fitting a new bellcast bead at the base, or making good around a new window. Matching painted render is rarely a problem, because the whole wall can be repainted. With older through-coloured finishes, sunlight changes the colour over time, so a repair may look a shade different at first. We’ll be upfront about that. Our checklist of signs your render needs repairing before winter is a good place to start.

Free, no-obligation quote in Coventry: WhatsApp me on 07453 614095 with a few photos, or send us a message.

Coventry’s housing and what it means for plaster and render

Victorian and Edwardian terraces

Earlsdon, Chapelfields, Spon End, Stoke, Hillfields and parts of Foleshill and Radford have older terraced houses. Chapelfields in particular is known for its 19th century watchmakers’ houses and workshops. Earlsdon has long streets of Victorian and Edwardian terraces and some larger houses.

Expect solid nine-inch brick walls and, under the layers of paint, a soft lime plaster that has been cut into and filled more times than anyone can count. New wiring, central heating, a damp-proof course, the odd blocked fireplace: each left its mark. A typical brief here is to re-plaster the bottom metre or so of the ground-floor walls once damp works are complete, rebuild a chimney breast, deal with a lath and plaster ceiling that has started to bow, and finish a knocked-through kitchen-diner. On walls like these, we’d rather use a breathable plaster than seal in moisture with gypsum. Earlsdon and Chapelfields are both conservation areas, which matters if the outside is on your list too.

Interwar semis

As Coventry’s industries grew between the wars, large numbers of semis were built in areas such as Coundon, Radford, Stoke, Cheylesmore, Styvechale and Allesley Park. Bay windows, hipped roofs and a pebbledashed or rendered upper storey are typical.

These are sturdy houses, but by now the inside walls usually carry decades of wallpaper scars and filler, and the ceilings are often cracked. Whole-room skims, new ceilings and plastering the opening when the front and back rooms are joined are bread-and-butter jobs. Outside, the pebbledash is often hollow in places. Owners either have it repaired and painted, or have it removed and replaced with a silicone or through-coloured finish, checking planning first.

Post-war estates and the rebuilt city

Much of Coventry’s city centre was rebuilt after wartime bombing, and large estates were built in the post-war decades in places such as Tile Hill, Canley, Willenhall, Bell Green, Wood End and Wyken. They include houses, maisonettes and flats, and a share of them were put up using non-traditional building systems rather than ordinary brick. Inside you’ll often find textured ceilings and boards whose joints have cracked. Outside, the construction type decides what can safely be rendered, so mention it when you first get in touch if you know or suspect your home isn’t standard brick.

Newer homes, flats and student housing

Newer developments around the edges of the city and across brownfield sites, plus the many city-centre flats and student blocks, mostly use plasterboard on dabs or metal studs. Jobs include fixing settlement cracks and popped screws, skimming over taped joints that show through, and boarding out conversions.

Coventry also has a lot of shared student housing near both universities, particularly around Earlsdon, Canley and the city centre. These houses take more wear than most, and landlords often need walls and ceilings repaired between tenancies.

Planning, conservation areas and building control in Coventry

Plastering inside your home is almost never a planning matter. Rendering the outside can be. Before you book any outside work in Coventry, run through these three checks. This is general guidance, so confirm the details with Coventry City Council, which is the planning authority for the city. Villages just beyond the city, such as Baginton and Binley Woods, are in Warwickshire and come under a different council, so check your council tax bill if you’re near the edge.

Check 1: Will the house look different?

Houses have permitted development rights that cover a lot of minor work. Re-rendering in a finish that looks much like the existing one usually falls within them. Rendering over bare brick, or swapping a cream sand and cement finish for a dark grey silicone, changes the look, and that can need a planning application. Flats and maisonettes don’t get the same rights as houses, so for them permission is more often needed.

Check 2: Is the property in a conservation area or covered by an Article 4 Direction?

Conservation areas count as designated land, and on designated land, rendering any part of a house’s exterior isn’t permitted development. You’ll need to apply. Coventry also has Article 4 Directions in places, which take away further rights. And if the building is listed, significant work needs listed building consent, whether it’s outside or in.

Coventry City Council’s website lists 19 conservation areas:

Earlsdon and Brownshill Green are the newest, both enacted in November 2022. The council publishes a boundary map for each area and shows them on its online planning map, and its conservation team can be contacted at conservation@coventry.gov.uk. If an application is needed, we can provide product data sheets, colour cards and photos of the wall to go with it.

Check 3: Does building control need to know?

Here the trigger is energy efficiency rather than appearance. Approved Document L classes rendering the outside face of a wall, or taking a wall back to bare masonry and rebuilding it, as renovation of a thermal element. Once that covers more than 50% of a given wall, the expectation is that the whole wall is upgraded for insulation, so far as it’s technically, functionally and economically feasible. Insulated render always needs building regulations sign-off. For a full re-render or insulated render, talk to building control early, either the city council’s team or a registered building control approver, and we’ll build their requirements into the job.

Problems we often see in Coventry homes

Damp on ground-floor walls

Older terraces in Earlsdon, Chapelfields and Stoke often show damp along the bottom of ground-floor walls. The cause might be a bridged or failed damp-proof course, garden or pavement levels that have crept up, leaking pipes or condensation. Fix the cause first. Then we can re-plaster with materials that suit the wall, following any specification from a damp-proofing contractor.

Wear and tear in shared houses

Student and shared houses take a lot of knocks: damaged corners, holes from fixings, scuffed walls and ceilings stained by leaks from bathrooms. We repair these quickly between tenancies, and where a room has more patches than wall, a full skim gives a better finish.

Cracked ceilings in post-war homes

Straight-line cracks in ceilings are usually the joints between plasterboard sheets opening up. They tend to come back after filling. Over-boarding, or re-taping and skimming, gives a lasting fix.

Hollow pebbledash

Pebbledash on interwar and post-war houses often goes hollow in patches. If you tap it and it sounds hollow, it’s no longer properly bonded. Small areas can be repaired, but widespread hollow areas usually mean it’s time to remove and re-render.

Plastering a Coventry terrace: where we fit in

Many of our Coventry jobs are part of bigger work on an older terrace, whether it’s a first home in Earlsdon, a family house in Stoke or a rental in Foleshill. These projects go much more smoothly when everyone knows the order.

Strip-out comes first: old kitchens and bathrooms out, wallpaper off, and any plaster that’s clearly failing hacked off. That’s the moment to find out what you’re dealing with, because old plaster often hides cracked lintels, leaking pipes, failed pointing or damp. Deal with those before anything new goes on.

Next, the electrician and plumber do their first fix. Any structural work, such as a steel for a knock-through, should be finished and signed off. Then we come in to board ceilings and stud walls, plaster and re-plaster where needed, and patch every chase in one go. After that, the house needs drying time. In an older terrace with solid walls, especially in winter, that can be longer than people expect.

Once the plaster is dry, second fix trades can fit sockets, radiators, kitchens and skirting, and decorators can start with a mist coat. If a rear wing or the back of the house is being rendered, we’ll schedule that for suitable weather, often while inside work dries.

Choosing a render for your Coventry home

If you’re thinking about rendering, here’s a short guide to which system tends to suit which house. We’ll always look at your wall before recommending anything.

Turning round a rental property

If you let property in Coventry, you’ll know that the gap between tenants is short. The quickest way to get plastering done in that window is to send us photos as soon as the previous tenants leave, or even from the check-out report. We’ll tell you what’s needed, how long it will take and how long the plaster needs before the decorator can start, so you can plan the re-let date realistically. We can also arrange access directly with your letting agent.

How a Coventry job runs

Getting a quote

Start by sending us photos on WhatsApp (07453 614095): wide shots of each wall or ceiling, close-ups of any cracks or damp, and the outside of the house if it’s render. Add rough sizes and your postcode. For a rental, give the address and who holds the keys. Straightforward work can often be quoted from the pictures. If there’s damp, a ceiling that’s dropping, a large render job or a conservation area involved, we’ll book a visit first.

The quote comes in writing and lists what’s covered, such as making good, beads, boards, protection and taking the rubbish away, so it can be compared fairly with any others you get.

On site

Before we arrive

Empty the room if you can, or push everything to the middle. Take down curtains and anything on the walls. If sockets and switches need easing off the wall so we can plaster behind them, that’s a job for an electrician. For render, clear a path round the house and tell us where we can park.

Drying times and aftercare

Plaster: dos and don’ts

New plaster starts a deep brown-pink and lightens as the water leaves it. When it’s pale and even all over, it’s dry. Thin skims get there in a matter of days. Re-plastered walls with thick backing coats can take a week or two, and an unheated empty house in January will take longer again.

Do crack a window and keep internal doors open so damp air can escape. Do keep the heating gentle and steady. Do start decorating with a mist coat, which is matt emulsion thinned with water so it soaks into the surface. Don’t aim fan heaters or dehumidifiers straight at the wall at full blast, which can cause cracking. Don’t use vinyl or wipe-clean paints on brand new plaster, as they can seal in moisture that’s still escaping.

The full detail is in our guide on how long plaster takes to dry before painting.

Render: looking after it

Render is weather-dependent while it cures: freezing nights, downpours and fierce sun can all spoil the finish, so we’ll pick the days carefully. Silicone and through-coloured finishes are done once they’ve cured. Sand and cement needs time to cure properly before a breathable masonry paint goes on.

After that, maintenance is mostly about water. Keep gutters and downpipes flowing, sort leaks quickly, don’t let flower beds or new patios rise above the bottom edge of the render, and if green algae appears, use a soft brush and a suitable cleaner rather than a pressure washer.

How to choose a plasterer in Coventry

A five-minute conversation tells you a lot. Here’s what to ask, and what a good answer sounds like.

What shapes your plastering quote in Coventry

A “standard room” doesn’t really exist. Here’s what actually moves a quote up or down, grouped so it’s easier to think about.

The surface

How much area there is, and what state it’s in. Sound walls take a skim. Hollow, damp-damaged or wildly uneven walls need cutting back, re-plastering or boarding first. Textured ceilings need sealing or boarding, and any asbestos test is arranged separately. High ceilings and lath and plaster take longer.

The building

The render system you choose (sand and cement, silicone, through-coloured or insulated), the number of windows and doors, reveals, sills, corners and beads, and whether old plaster, pebbledash or render has to come off and be taken away. Non-traditional construction may need a particular system.

The logistics

Scaffold or access towers, narrow alleys between terraces, parking, how far materials have to be carried, whether rooms are empty, and how tight the deadline is, for example a rental that has to be ready for new tenants.

Photos on WhatsApp to 07453 614095 are the quickest way to a realistic figure.

Nearby areas we cover

We cover all of Coventry and the towns and villages around it. These pages have more detail:

See all our plastering and rendering services.

Plastering in Coventry’s post-war homes

After the Blitz, large parts of the city were rebuilt, and many streets on the edges were filled with council and private houses through the 1950s and 60s. Their plaster is often a hard, thin finish over block or brick, and cracks tend to follow the lines of lintels and ceiling boards. Raking out, taping and re-skimming usually puts these right without full replastering.

Restoring period details

Many Victorian and Edwardian terraces in Earlsdon, Chapelfields and around the city still have plaster cornices, ceiling roses and picture rails, though years of paint can clog the detail. Where a section is cracked or missing, we can repair it or have a short length matched and fitted. Restoring these features is often simpler than people expect and keeps the character of a room. Where they’ve gone completely, plain coving is a simple way to finish the join between wall and ceiling.

More questions about plastering in Coventry

Do you work on student houses?

Yes. We repair, patch and skim between tenancies, and can work to a fixed date. Send the address, photos and when the house needs to be ready.

I live in Earlsdon. Can I render the front of my house?

Earlsdon became a conservation area in 2022, so rendering the outside of a house there needs planning permission. Check the council’s conservation area map and speak to its conservation team before planning any work.

Can you plaster over old lath and plaster?

Sometimes. If it’s firmly attached, it can be skimmed or over-boarded. If it’s sagging or crumbling, it may need taking down. We’ll check first.

Can you render over pebbledash?

If the pebbledash is firmly stuck, often yes. If it’s drummy or falling off, it has to come off first. Changing from pebbledash to a smooth or coloured finish alters how the house looks, so do the planning checks above before booking.

How soon can I paint new plaster?

When it’s an even pale colour all over. For a skim that’s often a few days, longer for thicker coats. Always use a mist coat first.

Can you work in my flat?

Yes. Inside, it’s no different from a house, though some blocks have rules on working hours and lifts. Any work to the outside of the building will usually need the freeholder’s or management company’s agreement.

Can you fix a ceiling damaged by a leak?

Yes. Get the leak repaired and let everything dry out first. Then we’ll cut out the stained or softened plasterboard, fit new and blend it in. If the rest of the ceiling is cracked too, over-boarding the whole thing usually gives a better overall result.

Do you cover villages outside the city?

Yes, including Kenilworth, Balsall Common, Berkswell, Meriden, Bedworth and the villages around them.

What render is best for a 1930s semi?

It depends on the wall and the look you want. Silicone and through-coloured renders are popular for their low maintenance, while sand and cement suits repairs and painted finishes. We’ll look at the wall and talk through the options.

Coventry homes we plaster

Coventry has watchmakers’ terraces, Edwardian streets, rows of interwar semis and the big post-war estates built as the city was rebuilt. Here’s where we work most, the homes you’ll find there and the plastering jobs that come up.

Whatever the house, RCR Connections Ltd puts 62 years of combined experience into it. We’re Birmingham based, covering the whole of the Midlands, and we work Monday to Friday 7am to 5pm and Saturday 7am to 1pm. WhatsApp me on 07453 614095 or message the page with photos of the room and your road or postcode in Coventry.

Outside, we also fit K-Rend monocouche and silicone render, see rendering in Coventry. A few miles south, we’re also the plasterer in Kenilworth.

What our customers say

Was amazed by the punctuality from them as far as tradesmen go and the experience was stress-free with a great finish to my maisonette.

James Tranter

We chose them for our home extension, and the transformation was amazing. Their work is top-notch, and I’d recommend them to anyone seeking both quality and luxury in construction.

Emma S

These guys were great lads, grafted hard, and was really happy with the price and the end result. Blimey, it was outstanding!

Michael T

Very impressed with the workmanship and attention to detail. The project was completed on time and exceeded my expectations!

Sophia Reynolds, Property Manager

More services: Plastering repairs · Plastering and coving · Plastering extensions and lofts.

Get a free quote in Coventry

WhatsApp a few photos to 07453 614095. You can also write to rcrconnectionsltd@gmail.com or fill in our contact page, and we’ll get back to you with a free, no-obligation quote. Our hours are 7am to 5pm Monday to Friday and 7am to 1pm on Saturday, and our office is at Studio 9, 50-54 St Paul’s Square, Birmingham B3 1QS.

Plastering in Coventry: common questions

Do you cover Coventry and the surrounding area?

Yes. RCR Connections Ltd is Birmingham based, covering the whole of the Midlands, and works across Coventry and the surrounding area. We also cover Kenilworth, Solihull and Birmingham. For the full list, see areas we cover.

How do I get a plastering quote in Coventry?

WhatsApp photos of the walls or ceilings to 07453 614095, with rough room sizes and what you would like done. We will come back with a free, no-obligation quote, or arrange a visit if the job needs a closer look.

Which parts of Coventry do you cover?

All of it. That includes Earlsdon, Chapelfields, Stoke, Stoke Park, Cheylesmore, Styvechale, Radford, Coundon, Tile Hill, Canley, Wyken, Walsgrave, Binley, Foleshill and Hillfields.

Can you replaster a room after a rewire?

Yes. A rewire leaves chases and patches all over the walls. We fill the chases, and if the old plaster has come away we take it back and replaster the whole wall or room, ready for decorating.

Do you replaster rented houses between tenants in Coventry?

Yes. We work for landlords and letting agents, patching damage, covering Artex and replastering rooms so the house is ready for decorating before the next tenant moves in.

How soon can I decorate after plastering?

A skim usually needs a few days to dry, and thicker backing coats need longer, depending on ventilation and the time of year. Wait until the plaster is an even pale colour all over, then start with a mist coat (watered-down emulsion).

Can you plaster over Artex?

Yes. We can skim over Artex, or over-board and skim ceilings that are cracked or uneven. If the Artex went up before 2000, have it tested for asbestos before anyone scrapes or sands it.

What hours do you work?

Monday to Friday 7am to 5pm and Saturday 7am to 1pm.

Popular areas we cover